Learning Objectives

Learning Objectives

By the end of this section, you will be able to do the following:

  • Explain acceleration and determine the direction and magnitude of acceleration in one dimension
  • Analyze motion in one dimension using kinematic equations and graphic representations
Section Key Terms
average acceleration instantaneous acceleration negative acceleration

Defining Acceleration

Defining Acceleration

Throughout this chapter we will use the following terms: time, displacement, velocity, and acceleration. Recall that each of these terms has a designated variable and SI unit of measurement as follows:

  • Time: t, measured in seconds (s)
  • Displacement: Δd, measured in meters (m)
  • Velocity: v, measured in meters per second (m/s)
  • Acceleration: a, measured in meters per second per second (m/s2, also called meters per second squared)
  • Also note the following:
    • Δ means change in
    • The subscript 0 refers to an initial value; sometimes subscript i is instead used to refer to initial value.
    • The subscript f refers to final value
    • A bar over a symbol, such as a ¯a ¯, means average

Acceleration is the change in velocity divided by a period of time during which the change occurs. The SI units of velocity are m/s and the SI units for time are s, so the SI units for acceleration are m/s2. Average acceleration is given by

a ¯ = Δv Δt = v f v 0 t f t 0 . a ¯ = Δv Δt = v f v 0 t f t 0 .

Average acceleration is distinguished from instantaneous acceleration, which is acceleration at a specific instant in time. The magnitude of acceleration is often not constant over time. For example, runners in a race accelerate at a greater rate in the first second of a race than during the following seconds. You do not need to know all the instantaneous accelerations at all times to calculate average acceleration. All you need to know is the change in velocity (i.e., the final velocity minus the initial velocity) and the change in time (i.e., the final time minus the initial time), as shown in the formula. Note that the average acceleration can be positive, negative, or zero. A negative acceleration is simply an acceleration in the negative direction.

Keep in mind that although acceleration points in the same direction as the change in velocity, it is not always in the direction of the velocity itself. When an object slows down, its acceleration is opposite to the direction of its velocity. In everyday language, this is called deceleration; but in physics, it is acceleration—whose direction happens to be opposite that of the velocity. For now, let us assume that motion to the right along the x-axis is positive and motion to the left is negative.

Figure 3.2 shows a car with positive acceleration in (a) and negative acceleration in (b). The arrows represent vectors showing both direction and magnitude of velocity and acceleration.

Two similar cars are shown. The first car is speeding up as indicated by a velocity vector and an acceleration vector pointing to the right. The second car is slowing down as indicated by a velocity vector pointing to the right and an acceleration vector pointing to the left. Unlabeled x and y-axes are shown for reference.
Figure 3.2 The car is speeding up in (a) and slowing down in (b).

Velocity and acceleration are both vector quantities. Recall that vectors have both magnitude and direction. An object traveling at a constant velocity—therefore having no acceleration—does accelerate if it changes direction. So, turning the steering wheel of a moving car makes the car accelerate because the velocity changes direction.

Virtual Physics

The Moving Man

With this animation in Figure 3.3, you can produce both variations of acceleration and velocity shown in Figure 3.2, plus a few more variations. Vary the velocity and acceleration by sliding the red and green markers along the scales. Keeping the velocity marker near zero will make the effect of acceleration more obvious. Try changing acceleration from positive to negative while the man is moving. We will come back to this animation and look at the Charts view when we study graphical representation of motion.

Grasp Check
Two similar cars are shown. The first car is speeding up as indicated by a velocity vector and an acceleration vector pointing to the right. The second car is slowing down as indicated by a velocity vector pointing to the right and an acceleration vector pointing to the left. Unlabeled x and y-axes are shown for reference.
Figure 3.4

Which part, (a) or (b), is represented when the velocity vector is on the positive side of the scale and the acceleration vector is set on the negative side of the scale? What does the car’s motion look like for the given scenario?

  1. Part (a). The car is slowing down because the acceleration and the velocity vectors are acting in the opposite direction.
  2. Part (a). The car is speeding up because the acceleration and the velocity vectors are acting in the same direction.
  3. Part (b). The car is slowing down because the acceleration and velocity vectors are acting in the opposite directions.
  4. Part (b). The car is speeding up because the acceleration and the velocity vectors are acting in the same direction.

Calculating Average Acceleration

Calculating Average Acceleration

Look back at the equation for average acceleration. You can see that the calculation of average acceleration involves three values: change in time, (Δt); change in velocity, (Δv); and acceleration (a).

Change in time is often stated as a time interval, and change in velocity can often be calculated by subtracting the initial velocity from the final velocity. Average acceleration is then simply change in velocity divided by change in time. Before you begin calculating, be sure that all distances and times have been converted to meters and seconds. Look at these examples of acceleration of a subway train.

Worked Example

An Accelerating Subway Train

A subway train accelerates from rest to 30.0 km/h in 20.0 s. What is the average acceleration during that time interval?

Strategy

Start by making a simple sketch.

A velocity vector and an acceleration vector are shown. The original velocity is zero kilometers per hour, and the final velocity is thirty kilometers per hour. The acceleration is unknown. Both vectors are pointing to the right, and the velocity vector is longer than the acceleration vector. Unlabeled x and y-axes are shown reference.
Figure 3.5

This problem involves four steps:

  1. Convert to units of meters and seconds.
  2. Determine the change in velocity.
  3. Determine the change in time.
  4. Use these values to calculate the average acceleration.
Solution
  1. Identify the knowns. Be sure to read the problem for given information, which may not look like numbers. When the problem states that the train starts from rest, you can write down that the initial velocity is 0 m/s. Therefore, v0 = 0; vf = 30.0 km/h; and Δt = 20.0 s.
  2. Convert the units.

    3.1 30.0 km h  ×  10 3 m 1 km  ×  1 h 3600 s  = 8.333  m s 30.0 km h  ×  10 3 m 1 km  ×  1 h 3600 s  = 8.333  m s
  3. Calculate change in velocity, Δv= v f –  v 0 = 8.333 m/s – 0 = + 8.333 m/s, Δv= v f –  v 0 = 8.333 m/s – 0 = + 8.333 m/s, where the plus sign means the change in velocity is to the right.
  4. We know Δt, so all we have to do is insert the known values into the formula for average acceleration.

    3.2 a ¯ = Δv Δt = 8.333m/s 20.0s =+0.417 m s 2 a ¯ = Δv Δt = 8.333m/s 20.0s =+0.417 m s 2
Discussion

The plus sign in the answer means that acceleration is to the right. This is a reasonable conclusion because the train starts from rest and ends up with a velocity directed to the right (i.e., positive). So, acceleration is in the same direction as the change in velocity, as it should be.

Worked Example

An Accelerating Subway Train

Now, suppose that at the end of its trip, the train slows to a stop in 8.00 s from a speed of 30.0 km/h. What is its average acceleration during this time?

Strategy

Again, make a simple sketch.

A velocity vector and an acceleration vector are shown. The original velocity is thirty kilometers per hour, and the final velocity is zero kilometers per hour. The acceleration is unknown. The velocity vector is longer than the acceleration vector and is pointing to the right. The acceleration vector is pointing to the left. Unlabeled x and y-axes are shown reference.
Figure 3.6

In this case, the train is decelerating and its acceleration is negative because it is pointing to the left. As in the previous example, we must find the change in velocity and change in time, then solve for acceleration.

Solution
  1. Identify the knowns: v0 = 30.0 km/h; vf = 0; and Δt = 8.00 s.
  2. Convert the units. From the first problem, we know that 30.0 km/h = 8.333 m/s.
  3. Calculate change in velocity, Δv= v f v 0 =08.333m/s=8.333m/s, Δv= v f v 0 =08.333m/s=8.333m/s, where the minus sign means that the change in velocity points to the left.
  4. We know Δt = 8.00 s, so all we have to do is insert the known values into the equation for average acceleration.

    3.3 a ¯ = Δv Δt = 8.333m/s 8.00s =1.04 m s 2 a ¯ = Δv Δt = 8.333m/s 8.00s =1.04 m s 2
Discussion

The minus sign indicates that acceleration is to the left. This is reasonable because the train initially has a positive velocity in this problem, and a negative acceleration would reduce the velocity. Again, acceleration is in the same direction as the change in velocity, which is negative in this case. This acceleration can be called a deceleration because it has a direction opposite to the velocity.

Tips For Success

  • It is easier to get plus and minus signs correct if you always assume that motion is away from zero and toward positive values on the x-axis. This way v always starts off being positive and points to the right. If speed is increasing, then acceleration is positive and also points to the right. If speed is decreasing, then acceleration is negative and points to the left.
  • It is a good idea to carry two extra significant figures from step-to-step when making calculations. Do not round off with each step. When you arrive at the final answer, apply the rules of significant figures for the operations you carried out and round to the correct number of digits. Sometimes this will make your answer slightly more accurate.

Practice Problems

A cheetah can accelerate from rest to a speed of 30.0 m/s in 7.00 s . What is its acceleration?
  1. 0.23 m/s 2
  2. 4.29 m/s 2
  3. 0.23 m/s 2
  4. 4.29 m/s 2
A women backs her car out of her garage with an acceleration of 1.40 m/s 2 . How long does it take her to reach a speed of 2.00 m/s ?
  1. 0.70 s
  2. 1.43 s
  3. 2.80 s
  4. 3.40 s

Watch Physics

Acceleration

This video shows the basic calculation of acceleration and some useful unit conversions.

Grasp Check
Why is acceleration a vector quantity?
  1. It is a vector quantity because it has magnitude as well as direction.
  2. It is a vector quantity because it has magnitude but no direction.
  3. It is a vector quantity because it is calculated from distance and time.
  4. It is a vector quantity because it is calculated from speed and time.
Grasp Check
What will be the change in velocity each second if acceleration is 10 m/s/s?
  1. An acceleration of 10 m/s/s means that every second, the velocity increases by 10 m/s .
  2. An acceleration of 10 m/s/s means that every second, the velocity decreases by 10 m/s .
  3. An acceleration of 10 m/s/s means that every 10 seconds , the velocity increases by 10 m/s .
  4. An acceleration of 10 m/s/s means that every 10 seconds , the velocity decreases by 10 m/s .

Snap Lab

Measure the Acceleration of a Bicycle on a Slope

In this lab you will take measurements to determine if the acceleration of a moving bicycle is constant. If the acceleration is constant, then the following relationships hold: v ¯ = Δd Δt = v 0 + v f 2 v ¯ = Δd Δt = v 0 + v f 2 If v 0 =0 v 0 =0 , then v f =2 v ¯ v f =2 v ¯ and a ¯ = v f Δt a ¯ = v f Δt

You will work in pairs to measure and record data for a bicycle coasting down an incline on a smooth, gentle slope. The data will consist of distances traveled and elapsed times.

Safety Warnings
  • Find an open area to minimize the risk of injury during this lab.
Materials
  • stopwatch
  • measuring tape
  • bicycle
  1. Find a gentle, paved slope, such as an incline on a bike path. The more gentle the slope, the more accurate your data will likely be.
  2. Mark uniform distances along the slope, such as 5 m, 10 m, etc.
  3. Determine the following roles: the bike rider, the timer, and the recorder. The recorder should create a data table to collect the distance and time data.
  4. Have the rider at the starting point at rest on the bike. When the timer calls Start, the timer starts the stopwatch and the rider begins coasting down the slope on the bike without pedaling.
  5. Have the timer call out the elapsed times as the bike passes each marked point. The recorder should record the times in the data table. It may be necessary to repeat the process to practice roles and make necessary adjustments.
  6. Once acceptable data has been recorded, switch roles. Repeat Steps 3–5 to collect a second set of data.
  7. Switch roles again to collect a third set of data.
  8. Calculate average acceleration for each set of distance-time data. If your result for a¯a¯ is not the same for different pairs of Δv and Δt, then acceleration is not constant.
  9. Interpret your results.
Grasp Check

If you graph the average velocity (y-axis) vs. the elapsed time (x-axis), what would the graph look like if acceleration is uniform?

  1. a horizontal line on the graph
  2. a diagonal line on the graph
  3. an upward-facing parabola on the graph
  4. a downward-facing parabola on the graph

Check Your Understanding

Check Your Understanding

Exercise 1

What are three ways an object can accelerate?

  1. By speeding up, maintaining constant velocity, or changing direction
  2. By speeding up, slowing down, or changing direction
  3. By maintaining constant velocity, slowing down, or changing direction
  4. By speeding up, slowing down, or maintaining constant velocity
Exercise 2

What is the difference between average acceleration and instantaneous acceleration?

  1. Average acceleration is the change in displacement divided by the elapsed time; instantaneous acceleration is the acceleration at a given point in time.
  2. Average acceleration is acceleration at a given point in time; instantaneous acceleration is the change in displacement divided by the elapsed time.
  3. Average acceleration is the change in velocity divided by the elapsed time; instantaneous acceleration is acceleration at a given point in time.
  4. Average acceleration is acceleration at a given point in time; instantaneous acceleration is the change in velocity divided by the elapsed time.
Exercise 3
What is the rate of change of velocity called?
  1. Time
  2. Displacement
  3. Velocity
  4. Acceleration